Site Overlay

Configure Access Control Lists On A Cisco Asa 5500 Firewall

Configure Access Control Lists on a Cisco ASA 5500 Firewall

by

HELLOCSCO

The Cisco ASA 5500 is the Cisco firewall model series which followed the successful Cisco PIX firewall appliance. Cisco calls the ASA 5500 a security appliance instead of just a hardware firewall , because the ASA is not just a firewall. This device combines several security functionalities, such as Intrusion Detection, Intrusion Prevention, Content Inspection, Botnet Inspection, in addition to the firewall functionality.

However, the core ASA functionality is to work as a high performance firewall. All the other security features are just complimentary services on top of the firewall functionality. Having said that, the purpose of a network firewall is to protect computer and IT resources from malicious sources by blocking and controlling traffic flow. The Cisco ASA firewall achieves this traffic control using Access Control Lists (ACL).

[ad#embedded-square]

An ACL is a list of rules with permit or deny statements. Basically an Access Control List enforces the security policy on the network. The ACL (list of policy rules) is then applied to a firewall interface, either on the inbound or on the outbound traffic direction. If the ACL is applied on the inbound traffic direction (in), then the ACL is applied to traffic entering a firewall interface. The opposite happens for ACL applied to the outbound (out) direction.

The ACL permit or deny statements basically consist of source and destination IP addresses and ports. A permit ACL statement allows the specified source IP address/network to access the specified destination IP address/network. The opposite happens for deny ACL statements. At the end of the ACL, the firewall inserts by default an implicit DENY ALL statement rule which is not visible in the configuration.

Enough theory so far. Let us see some examples below to clarify what we have said above.

The basic command format of the Access Control List is the following:

[youtube]http://www.youtube.com/watch?v=oqtrpp0vYzc[/youtube]

ciscoasa(config)# access-list access_list_name extended {deny | permit} protocol source_address mask [source_port] dest_address mask [ dest_port]

To apply the ACL on a specific interface use the access-group command as below:

ciscoasa(config)# access-group access_list_name [in|out] interface interface_name

Example1:

Allow only http traffic from inside network 10.0.0.0/24 to outside internet

ciscoasa(config)# access-list HTTP-ONLY extended permit tcp 10.0.0.0 255.255.255.0 any eq 80

ciscoasa(config)# access-group HTTP-ONLY in interface inside

The name HTTP-ONLY is the Access Control List itself, which in our example contains only one permit rule statement. Remember that there is an implicit DENY ALL rule at the end of the ACL which is not shown by default.

Example2:

Deny telnet traffic from host 10.1.1.1 to host 10.2.2.2 and allow everything else.

ciscoasa(config)# access-list DENY-TELNET extended deny tcp host 10.1.1.1 host 10.2.2.2 eq 23

ciscoasa(config)# access-list DENY-TELNET extended permit ip host 10.1.1.1 host 10.2.2.2

ciscoasa(config)# access-group DENY-TELNET in interface inside

The above example ACL (DENY-TELNET) contains two rule statements, one deny and one permit. As we mentioned above, the access-group command applies the ACL to an interface (either to an inbound or to an outbound direction).

Example3:

The example below will deny ALL TCP traffic from our internal network 192.168.1.0/24 towards the external network 200.1.1.0/24. Also, it will deny HTTP traffic (port 80) from our internal network to the external host 210.1.1.1. All other traffic will be permitted from inside.

ciscoasa(config)# access-list INSIDE_IN extended deny tcp 192.168.1.0 255.255.255.0 200.1.1.0 255.255.255.0

ciscoasa(config)# access-list INSIDE_IN extended deny tcp 192.168.1.0 255.255.255.0 host 210.1.1.1 eq 80

ciscoasa(config)# access-list INSIDE_IN extended permit ip any any

ciscoasa(config)# access-group INSIDE_IN in interface inside

How to

configure Access Control Lists (ACL) on Cisco ASA 5500 firewalls

? An ACL is the central configuration feature to enforce security rules on your network.

Article Source:

ArticleRich.com